ESC600-4T ダイヤモンドワイヤーソー切断機

主駆動モーター出力: 2kW
総重量: 3500 kg.
全体の寸法: 長さ3800mm×幅3000mm×高さ2800mm
切断範囲: 2000mm×600mm×600mm以内 (長さ×幅×高さ)
Y軸用変位サーボモータ動力: 1.5kW; Z軸用: 1.5kW
切断ライン速度: 0-40MS, 調整可能な
切断線径: 0.35-0.8mm
冷却方法: 水の循環

製品説明:

ESC600-4Tシリコンロッド切断機は、ロッド型の単結晶シリコンの定量的セグメンテーションのために設計された特殊なワイヤーソーです (多結晶シリコン). 切削工具には自社開発の円形ダイヤモンドワイヤを使用しており、0.35mmの円形ダイヤモンドワイヤに対応しています。, 0.45mm, 0.5mm, 直径0.6mm.

diamond-wire-saw-cutting-machine-5555

動作原理:

ESC600-4Tシリコンロッド切断機は、切断中にシリコンロッドをワークテーブルに配置します. 切断サイズの要件に応じて、マークされた位置でカットが作成されます. シリコンロッドを移動する必要はありません; ワークテーブルは、プログラムされた設定に基づいて適切な寸法を水平に供給して、定量的セグメンテーション切断を実現します. 水平方向の動きは、変位サーボモーターによって駆動されます, 正確なサイジングを確保します, 0.5mmの薄い材料をカットする機能を備えています. 円形のダイヤモンドワイヤーは、特殊な切削工具として機能します, 最小限の切断ノイズを生成します, 低エネルギー消費, 高い切削能率, 小型KERFによる材料の浪費の減少, シリコンロッドの滑らかな表面, 達成 “研削で切る” 効果. このマシンは、湿った状態と乾燥状態の両方のための二重目的の切断機です, さまざまな作業条件での棒材の切断に適しています。. 最大長さおよび直径が 2000mm x 600mm までのクリスタルロッドサイズを切断できます。.

diamond-wire-saw-cutting-machine--9999

製品の特徴:

この装置の主な利点は次のとおりです:

  1. 装置は切断部分が移動する設計を採用しています。, ワークではなく, コンパクトな構造を実現. 同じ長さの棒材の場合, 装置の外形寸法がほぼ半分になりました.
  2. シリコン素材の独特な特性により、, 切断コンポーネントの移動システムは、より一般的なネジ ガイド レールの代わりにハード レールを使用します。. ハードレールには、線路上の硬化したシリコンスラッジを処理する際に、かけがえのない利点があります。, トラックの寿命が長くなっています 6 年 (当社の最初のハードレール装置は、 6 年, 今後も増加する可能性のある数字).
  3. シリコンロッドの切断面の平行度を確保するため, このアプローチには、切断の平行度を保証するためにシリコンロッド材料を一度クランプし、それ以上動かすことなくクランプするスキームが含まれます。. さらに, 弾性サポートの革新的な使用により、切断中のエッジ欠けの問題が大幅に軽減されます。, 刃欠けデータ5mm以内.
  4. サポートプラットフォームは、異なる直径のシリコンロッド材料の切断に対応するために、V 字型の開口部のサイズを調整できます。, 1 つのデバイスを製品仕様のほぼ全範囲に適応できるようにする.
  5. 油圧リフティングローディングテーブルによりローディングが容易になり、シリコンロッドを任意の位置で切断する際にサポートコンポーネントに切り込みが発生するという問題が解決されます。, 複雑な問題を単純な解決策で解決する (ピアの複雑なソリューションを参照する).
  6. 弾性力センサーを備えた革新的な張力スキームにより、線数の変化に応じて張力が増加します。. 同時に, ワイヤーの弓が切断されるとき、張力はその切断サイクルの最大値に維持されます。, スムーズな移行を可能にする.
  7. インテリジェントな張力保護システムは、動作していないときに切断システムの張力を自動的に解放し、ワイヤーとプーリーの溝を損傷から保護します。. 稼働状態に入るとき, 張力を必要なレベルに素早く調整します。 2 秒.
  8. 連続ワイヤ交換システムは、動作中にワイヤ張力をゆっくりと高めることで、ワイヤ交換段階での異常なワイヤ断線の確率をほぼゼロに下げることに成功しました。.
  9. さまざまなフェールセーフ設計と安全保護がテストされています, 蓄積された, 一定期間にわたって検証され、 6 年.

Frequently Asked Questions

What materials can the ESC600-4T cut?

The ESC600-4T is purpose-built for the quantitative segmentation of rod-shaped monocrystalline and polycrystalline silicon. It uses a closed-loop diamond wire as the cutting tool and is also suitable for cutting other rod-type materials under various working conditions.

What is the maximum workpiece size?

The cutting range is 2000 mm × 600 mm × 600 mm (length × width × height). Silicon rods are clamped once and do not need to be repositioned during the cut, which is what keeps the cut faces parallel.

Which diamond wire diameters does it support?

The machine accepts closed-loop diamond wire from 0.35 mmから 0.8 mm in diameter. Because kerf width follows wire diameter, thinner wire means less material lost per cut.

What cutting speed can it reach?

Cutting line speed is adjustable from 0 に 40 MS. The worktable is driven by a Y-axis and Z-axis displacement servo motor (1.5 kW each), so the feed can be programmed to match the section thickness required.

How does it keep edge chipping under control?

Two things work together: the silicon rod is clamped once and never moved during the cut, and the support platform uses an elastic support design that significantly reduces chipping. Measured edge chipping stays within 5 mm, and sections as thin as 0.5 mm can be produced.

Why does it use hard rails instead of screw guide rails?

Silicon sludge hardens on the track and quickly degrades screw-type guide rails. Hard rails tolerate that condition far better — our first hard-rail machine has been running for six years and the track is still within tolerance.

Can it run both wet and dry?

The machine is designed for both wet and dry operating conditions. Whether dry cutting is appropriate depends on the material being cut — some materials require coolant for chip removal and surface quality. Please confirm the intended material with us and we will advise the correct configuration.

What are the power, weight and footprint?

Main drive motor is 2 kW; total weight is 3500 kg; overall dimensions are 3800 mm × 3000 mm × 2800 mm. Because the cutting assembly moves instead of the workpiece, the machine occupies roughly half the floor space of a conventional design handling rods of the same length. Cooling is by water circulation.